Phonetics 2000 User Manual Page 85
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
85
Chapter 6: Operation
Alarm Acknowledgment - Alphanumeric Pager Dialout
CPP Monitor 2000 will dial out to your alphanumeric pager service
and leave a message on the display of your pager. (See Program-
ming Section, Chapter Four, for dialing to beepers/pagers). The unit
will then hang up without speaking a voice message and wait for
callback acknowledgment. This waiting period is called the
“intercall delay time.” During this time you may call the unit back
from a Touch-Tone phone to receive a report of the alarm condition
and acknowledge the alarm by entering the acknowledgment code.
NOTE: An alarm cannot be acknowledged using a
pulse (rotary) telephone.
Below is an example of what CPP Monitor 2000 will say when you
call it back to acknowledge a typical alarm:
“Hello, this is (ID message)”
Input 1, closed, alarm exists
“Hello, this is (ID message)”
Input 1, closed, alarm exists
“Hello, this is (ID message)”
Input 1, closed, alarm exists
“Enter acknowledgment code.”
CPP Monitor 2000 will now wait 5 seconds for the Touch-Tone
acknowledgment code to be entered. After the last digit of the
acknowledgment code has been received, CPP Monitor 2000 will
respond by saying, “Alarm Acknowledged.” The alarm has been
acknowledged and the unit will hang up. Once the alarm has been
acknowledged, the dialout process stops.
If the Touch-Tone acknowledgment code is not received, CPP
Monitor 2000 will respond by saying: “beep,” “error,” “goodbye.” The
alarm has not been acknowledged. CPP Monitor 2000 will hang up
- CPP Monitor 2000 1
- Contents 2
- Important Safety Instructions 11
- FCC Requirements 12
- Chapter 1: Introduction 17
- Programming Interface 18
- Technical Support 18
- About This Manual 18
- Chapter 2: Installation 21
- POWER SURGE PROTECTION 22
- BATTERY BACKUP 22
- TELEPHONE LINE 23
- INPUT CONFIGURATION 24
- LED INDICATORS 26
- Chapter 3: Communications 27
- Running the Software 28
- CPP Monitor 2000 Menu Bar 29
- Communications Setup 30
- Modem Setup 30
- Communication Status 31
- Advanced Comm Setup 32
- Options screen 34
- Chapter 4: Programming 35
- Procedure 36
- Local Communication 37
- Modem Communication 37
- Off-line Communication 38
- To create a Data File: 38
- SYSTEM PROGRAMMING 39
- System Identification 40
- Unit Phone Number: 40
- Unit Description: 40
- Default setting: On 41
- Alpha Pager Speed 42
- Maximum Calling Rounds 42
- Voice Repetitions 42
- Acknowledgment Code 42
- Voice Password 42
- Slave ID 43
- Passwords 43
- Incoming Calls: 43
- Rings Until Answer 43
- Carrier Wait Time 43
- Status tab: 44
- Min & Max: 45
- Configuration tab: 46
- Calibration: 47
- Label/Units: 47
- Alarm Programming tab: 48
- Alarm High Limit: 49
- Recognition Time: 49
- Call List: 49
- MONITORS 50
- Delete Input Monitors 51
- Bar Reading: 51
- Low Limit: 51
- High Limit: 51
- Low Alarm Limit: 51
- High Alarm Limit: 52
- Minimum Input Reading: 52
- Maximum Input Reading: 52
- Gauge Reading: 52
- DESTINATIONS 54
- Destination: 55
- Special Dialing Codes: 56
- Call Zones: 57
- Alarm Call Mode: 58
- Disabled: 58
- Until Acknowledged: 58
- Dial Type: 60
- DATALOGGING 61
- Interval: 62
- Use Start Time: 63
- Start Time: 63
- Inputs Being Logged: 63
- Start/Stop datalogging: 63
- Downloading the Data Logger: 64
- Input selection: 65
- From Date and To Date: 65
- EVENT LOGGER 66
- Downloading the Event Logger: 67
- Viewing the Event Logger: 67
- Unit selection: 68
- Reset Event Logger: 69
- Event types: 69
- Query Times: 69
- Current Status: 70
- Data Logger: 70
- Report Interval: 70
- Global View: 72
- Settings: 73
- Print Event Log button 74
- Local Status Report 76
- Status Report 76
- Sample Status Report 77
- Chapter 6: Operation 79
- Alarm Dialout - Voice 80
- Alarm Dialout - Beeper 81
- Alarm Dialout - Modem 81
- ALARM ACKNOWLEDGMENT: 82
- PART TWO: REPORT DIALOUT 86
- PART THREE: CALL-IN STATUS 87
- Enabling Auto Answer Mode 89
- Enabling Polling Mode 89
- APPENDIX A 91
- System Events List 91
- APPENDIX B 93
- Engineering Specifications 93
- Datalogging 94
- Communication 94
- Programming 95
- Visual Indicators 95
- Environmental 95
- Physical 95
- Approvals 96
- Warranty 96
- 2.8K Thermistor Data 97
- 10K Thermistor Data 98
- APPENDIX D 99
- RS232 Specifications 99
- APPENDIX E 101
- Modbus Protocol 101
- Appendix E: Modbus Protocol 103
- COMMUNICATIONS 109
- Cause SolutionProblem 110
- Appendix F: Troubleshooting 111
- MONITORING 112
- III: TEMPERATURE 112
- ENERAL P 113
- Problem 114
- Cause Solution 114
- APPENDIX G 115
- Accessories 115
- Terminal Block 117
© 2020, manymanuals.com. All rights reserved. | 0.628 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals