Phonetics 2000 User Manual Page 22
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
22
CPP Monitor 2000 User’s Manual
POWER SURGE PROTECTION
The CPP Monitor 2000 can be damaged by power surges and
lightning through the telephone line and the power supply. Although
the unit has built-in surge protection, we strongly recommend that
additional protection be obtained for the unit and for any electronic
equipment that is attached to your power supply and telephone lines.
Power surge protection is especially important if you live in a
lightning-prone area.
BATTERY BACKUP
The CPP Monitor 2000 has a compartment for 6 “C” cell Nickel-
Cadmium rechargeable batteries (not included). Be sure to use
quality batteries that are rated for at least 2200mAhr. These will
provide approximately 10-15 hours of unit operation in the event of
a power failure.
NOTE: Use ONLY Nickel-Cadmium rechargeable
batteries.
The unit will constantly recharge the batteries whenever the power
switch is turned on and the unit is plugged into a power supply.
Also, a 3V lithium battery is included for memory storage, to retain
user programming. This battery should provide at least 2 years of
service without power, and up to 10 years of intermittent use.
Turning the CPP Monitor 2000 on
Thread the power supply cord through the strain relief ring next to
the power jack, and plug it in. Then plug the transformer into a
115VAC 60Hz outlet. The ring anchors the cord, protecting the plug
and jack. Slide the power switch to ON to start the unit. The
System-On LED should glow steadily.
CPP Monitor 2000 Rear View
Electrical Jack
Strain Relief
Support Ring
- CPP Monitor 2000 1
- Contents 2
- Important Safety Instructions 11
- FCC Requirements 12
- Chapter 1: Introduction 17
- Programming Interface 18
- Technical Support 18
- About This Manual 18
- Chapter 2: Installation 21
- POWER SURGE PROTECTION 22
- BATTERY BACKUP 22
- TELEPHONE LINE 23
- INPUT CONFIGURATION 24
- LED INDICATORS 26
- Chapter 3: Communications 27
- Running the Software 28
- CPP Monitor 2000 Menu Bar 29
- Communications Setup 30
- Modem Setup 30
- Communication Status 31
- Advanced Comm Setup 32
- Options screen 34
- Chapter 4: Programming 35
- Procedure 36
- Local Communication 37
- Modem Communication 37
- Off-line Communication 38
- To create a Data File: 38
- SYSTEM PROGRAMMING 39
- System Identification 40
- Unit Phone Number: 40
- Unit Description: 40
- Default setting: On 41
- Alpha Pager Speed 42
- Maximum Calling Rounds 42
- Voice Repetitions 42
- Acknowledgment Code 42
- Voice Password 42
- Slave ID 43
- Passwords 43
- Incoming Calls: 43
- Rings Until Answer 43
- Carrier Wait Time 43
- Status tab: 44
- Min & Max: 45
- Configuration tab: 46
- Calibration: 47
- Label/Units: 47
- Alarm Programming tab: 48
- Alarm High Limit: 49
- Recognition Time: 49
- Call List: 49
- MONITORS 50
- Delete Input Monitors 51
- Bar Reading: 51
- Low Limit: 51
- High Limit: 51
- Low Alarm Limit: 51
- High Alarm Limit: 52
- Minimum Input Reading: 52
- Maximum Input Reading: 52
- Gauge Reading: 52
- DESTINATIONS 54
- Destination: 55
- Special Dialing Codes: 56
- Call Zones: 57
- Alarm Call Mode: 58
- Disabled: 58
- Until Acknowledged: 58
- Dial Type: 60
- DATALOGGING 61
- Interval: 62
- Use Start Time: 63
- Start Time: 63
- Inputs Being Logged: 63
- Start/Stop datalogging: 63
- Downloading the Data Logger: 64
- Input selection: 65
- From Date and To Date: 65
- EVENT LOGGER 66
- Downloading the Event Logger: 67
- Viewing the Event Logger: 67
- Unit selection: 68
- Reset Event Logger: 69
- Event types: 69
- Query Times: 69
- Current Status: 70
- Data Logger: 70
- Report Interval: 70
- Global View: 72
- Settings: 73
- Print Event Log button 74
- Local Status Report 76
- Status Report 76
- Sample Status Report 77
- Chapter 6: Operation 79
- Alarm Dialout - Voice 80
- Alarm Dialout - Beeper 81
- Alarm Dialout - Modem 81
- ALARM ACKNOWLEDGMENT: 82
- PART TWO: REPORT DIALOUT 86
- PART THREE: CALL-IN STATUS 87
- Enabling Auto Answer Mode 89
- Enabling Polling Mode 89
- APPENDIX A 91
- System Events List 91
- APPENDIX B 93
- Engineering Specifications 93
- Datalogging 94
- Communication 94
- Programming 95
- Visual Indicators 95
- Environmental 95
- Physical 95
- Approvals 96
- Warranty 96
- 2.8K Thermistor Data 97
- 10K Thermistor Data 98
- APPENDIX D 99
- RS232 Specifications 99
- APPENDIX E 101
- Modbus Protocol 101
- Appendix E: Modbus Protocol 103
- COMMUNICATIONS 109
- Cause SolutionProblem 110
- Appendix F: Troubleshooting 111
- MONITORING 112
- III: TEMPERATURE 112
- ENERAL P 113
- Problem 114
- Cause Solution 114
- APPENDIX G 115
- Accessories 115
- Terminal Block 117
© 2020, manymanuals.com. All rights reserved. | 0.193 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals